-40%
SHIFT CABLE ASSY, Auto Trans Shift Cable, GEAR SELECT CABLE for SUZUKI VITARA
$ 69.69
- Description
- Size Guide
Description
AUTOMATIC TRANSMISSION SHIFTER CABLE, GEAR SELECT CABLE#2 In Image
GENRALLY FITS 1999 - 2005 SUZUKI VITARA, Some SUZUKI GRAND VITARA and some Grand Vitara XL-7 . (
SEE THIS LISTING AND MY OTHER LISTING FOR XL-7)
Doesn't fit all, send VIN # before purchase if not sure.
Suzuki
Vitara
2003
Base
2.0L L4 - Gas 2.5
2002 Suzuki Vitara
Suzuki
Vitara
2002
JLS, JLX
2.0L L4 - Gas, 2.5
2001 Suzuki Vitara
Suzuki
Vitara
2001
JLS, JLX, JS, JX
1.6L L4 - Gas, 2.0L L4 - Gas, 2.5
2000 Suzuki Vitara
Suzuki
Vitara
2000
JLS, JLX, JS, JX
1.6L L4 - Gas, 2.0L L4 - Gas 2.5
1999 Suzuki Vitara
Suzuki
Vitara
2000
JLS, JLX, JS, JX
1.6L L4 - Gas, 2.0L L4 - Gas 2.5
Suzuki SQ416L,
SQ625L,
SQ632 Early Model, Later model takes different One (COMPARE PIC AT ENDS OR SEND VIN #)
2002 JLS for example has two choices
2004-2005 VITARA / GRAND VITARA (COMPARE PIC TO INSURE CORRECT FIT)
SUZUKI GRAND VITARA DIESEL (COMPARE PIC TO INSURE CORRECT FIT
SUZUKI GRAND VITARA XL-7 (JA627)
(AT:~JS3TY92V?14106520, ~JS3TX92V?14117617)
COMPARE PIC TO INSURE CORRECT FIT AND/OR SEE MY OTHER XL-7 LISTING (There are two different options for JA627. The JA420 appears to be my other listing)
Reserve the right to substitute with Genuine OEM SUZUKI Motors or General Motors Corporation direct fit product if applicable
Basic Installation Instructions – Yours may vary
Slide seats forward, remove two side Philips screws from E-Brake console and remove e-brake console and set on driver seat or disconnect wires to fully remove.
Slide seats back, remove two plastic pins at side rear of shift console by prying out with flat screwdriver and remove two front side Philips screws. Remove shift console and unplug wiring to the N/P switch.
12 MM unbolt the shift lock release
and using needle nose slide off of the bushing.
Unbolt the 4
12MM from the shift console. Remove it to expose the cable.
(This is a good time to do a visual from under the vehicle to see how the cable comes from the shifter to the transmission.)
Pull the pin and slide off the shifter. Remove from bracket.
At transmission, - using two 10 mm to disconnect from Transmission. Slide off or break off bracket.
Before installing,
clean both brackets of rust and where it locks in to the groves. The expanded rust can offer
resistance/damage
if not cleaned with wire brush.
When installing, guide it from under the vehicle along the passenger side top and then down.
If you cleaned the brackets well, the new should slide into the bracket and lock in without
much resistance.
PRECAUCIÓN
: LIMPIE EL ÓXIDO DE DOS SOPORTES METÁLICOS O REEMPLAZAR.
EL PRODUCTO DEBE ENTRAR SIN FUERZA.
RETURNS -
SELLER DOES NOT ACCEPT RETURNS
WARRANTY / DEFECT
– THESE ARE INSPECTED BY US FOR VISIBLE ISSUES, 30 Day REPLACEMENT IF CONFIRMED MANUFACTURER DEFECT WITH PROFESSIONAL INSTALLATION